First Year

• Orientation And Basic Principles
• Tools and Blueprints
• First Aid/CPR/AED Training
• First Aid/CPR/AED Training
• Applied Math - Circuit Theory-Plans & Specs
• Conduit Bending
• Applied Math-Electrical Symbols & Outlets - Ohm’s Law
• General-Purpose and Small-Appliance Circuit
• Conductor Sizes, Types, & Connections - Type NM Cables
• Voltage Drop, Other Wiring Methods, and Printreading
• Mid-term Review and Exam
• Switch Control
• GFCI Protection
• Luminaires
• Front Bedroom Lighting and Introduction to Series Circuits
• Master Bedroom and Series Circuits
• Lighting and Small Appliance Branch Circuits
• Living Room and Study Branch Circuits - Introduction to Parallel Circuits
• Laundry Outlets and Parallel Circuits
• Garage Circuits and Parallel Circuit Calculations
• Conduit Fill and Special Purpose Outlets
• Special Purpose Outlets – Kitchen
• Special Purpose Outlets - Bathroom, Exhaust Fans and Hydromassage Tub
• Heating and Air Conditioning
• Low Voltage and Fire Alarms
• Recreation Room – Multiwire branch Circuits and Introduction to Combination Circuits
• Workshop Lighting and Receptacle Branch Circuits - Combination Circuits
• Service Entrance Equipment
• Knots, Rigging and Specialty Tools
• Overcurrent Protection
• Service Entrance Calculations
• Swimming Pools, Spas and Hot Tubs
• Home Automation, Standby Power and Review

Second Year

• Orientation, Safety Introduction to Meters, Feeder/Branch Circuits
• Service Calculations
• Services
• Conductor and Overcurrent Protection
• Grounding and Bonding Part I
• Grounding and Bonding Part II
• Wiring Methods
• Wiring Materials, Conduit and Box Fill
• Switches, Switchboards and Panelboards
• Equipment for General Use
• Introduction to AC Theory
• AC Theory I
• AC Theory II
• Single-Phase Transformers Part I
• Single-Phase Transformers Part II
• Power Generation, Three-Phase Transformers, Circuits, and Calculations
• Three-Phase Transformers, Delta-Delta
• Three-Phase Transformers, Delta-Wye
• Transformers for Non-Linear Loads, Three-Phase Fault Currents, Voltage Drop
• NEC Requirements for Transformers
• Transformers, Buck/Boost – Single and Three-Phase
• Generator and Transfer Switches
• Motors – Three-Phase
• Motors – Single Phase/DC
• Motors/Code – Branch Circuit Conductors
• Motors/Code – Branch Circuit
• Motors/Code – Starter/OL/Disc/Grounding
• Motors/Code – Locked Rotor/Phase Loss
• Motors/Code – Motor Feeders/Cond./OCPD

Third Year

• Registration & Orientation
• First Aid/CPR Review
• Construction Documents and Blueprint Reading Fundamentals
• Survey and Site Plans
• Structural, Architectural, and Mechanical Blueprints
• Electrical Branch Circuits, Feeders, and Lighting Blueprints
• Electrical Services and Service Entrance on Blueprints
• Specialty System Blueprint Reading
• Data, Voice, and Video Cabling using Copper Wiring
• Fiber Optics and Fiber Optic Systems
• 3-Phase Systems and Transformer Review/Harmonics
• Introduction to Grounding
• Conductors Used for Grounding, Bonding, and Systems
• Equipment Bonding and Ground Fault Protection
• Separately Derived Systems, Multiple Building Grounding, and Fault Current Calculations
• Grounding Review, Semester Review
• Electrical Quantities and Circuits
• Electrical Tools and Test Instruments/Safety
• Symbols, Logic and Line Diagrams
• Solenoids
• Contactors and Motor Starters
• Control Devices
• Motor Control Lab #1
• Motor Control Lab #2
• Reversing Circuits
• Time Delay and Counters
• Motor Control Lab #3
• Introduction to Fire Protection Signaling Systems – Conventional Systems
• Fire Alarm Systems Lab #1
• Installation, Start-up, Maintenance, and Troubleshooting of Fire Alarm Systems, and New Technology Systems
• Fire Alarm Systems Lab #2

Fourth Year

• Orientation & Safety
• Community First Aid & Safety
• Solid State Electronic Control Devices
• Electromechanical and Solid State Relays
• Advanced Controls Lab #1
• Photoelectric and Proximity Controls
• Programmable Controllers
• Advanced Controls Lab #2
• Reduced Voltage Starting
• Accelerating and Decelerating Methods
• Advanced Controls Lab #3
• Preventative Maintenance and Troubleshooting
• Advanced Controls Lab #4
• Leadership
• Using Digital Multimeters to Diagnose Power Quality
• National Electric Code and Related Standards, Safety Regulation, Power Systems
• Power Distribution Systems
• Services, Switchboards, and Panelboards
• Conductors and Overcurrent Protection Devices
• Grounding
• Designing and Installing Wiring Systems
• Branch and Feeder Circuits
• Receptacle and Lighting and Switching Outlets
• Motors and Compressor Motors
• Hazardous Locations
• Hazardous Locations, Special Types
• Signs and Sign Connections
• Load Calculations
• Final Code Review